Forum Lambert Benjamin Strona Główna Lambert Benjamin
Benjamin Lambert
 
 POMOCPOMOC   FAQFAQ   SzukajSzukaj   UżytkownicyUżytkownicy   GrupyGrupy   RejestracjaRejestracja 
 ProfilProfil   Zaloguj się, by sprawdzić wiadomościZaloguj się, by sprawdzić wiadomości   ZalogujZaloguj 

How to use laser to cut fr4 circuit board

 
Napisz nowy temat   Odpowiedz do tematu    Forum Lambert Benjamin Strona Główna -> milgetfstanel
Zobacz poprzedni temat :: Zobacz następny temat  
Autor Wiadomość
xysoom



Dołączył: 21 Lip 2019
Posty: 967

PostWysłany: Wto Sty 19, 2021 18:28    Temat postu: How to use laser to cut fr4 circuit board Odpowiedz z cytatem

How to use laser to cut fr4 circuit board


How to use laser to cut FR4 circuit board? There are some ways to use lasers with PCB. Here, we will learn about PCB Applications for lasers and PCB applications that are not suitable for lasers. Printed circuit board (PCB) is the most common in various electronic equipment. They use conductive paths to support and electrically connect electronic components from etched or signal traces of copper, and then laminate them onto a non-conductive substrate such as G10 or FR4.To get more news about fr4 board, you can visit pcbmake official website.

The vast majority of fr4 circuit boards are made by bonding a layer of copper on the entire substrate, then removing unwanted copper after applying a temporary mask (by etching), leaving only the desired trace of copper. Depending on the desired results, the epilog laser system can be used in the PCB field at various capacities. Here, we will study some different PCB Applications and their relationship with lasers.

1) Cut the label on the ready-made PCB board.

The following figure shows a circuit board that has been created. The operator can use the epilog laser system to cut holes with labels on each board so that they can be easily removed from the plate.

The best laser type for this application is fiber laser.

As long as there is no copper layer, epilog’s CO2 system will cut through PCB, while our fiber laser system (fibermark 24 and fusion M2 fiber laser) will cut through copper and copper free layers.

2) Mark graphics / text on the prefabricated PCB.

If you want to label printed circuit boards with barcodes, logos or serial numbers, our laser system can do the same.

The best system for this application: CO2 laser or fiber laser. When marking directly on PCB, our optical fiber and CO2 laser system can achieve low contrast marking. This is the application we want to test on the PCB used in your application lab to make sure it meets your needs.

Many PCB designs have various components. The PCB on the right contains a white area of engineering plastic that is ideal for barcodes, QR codes, or data matrix codes in this case.

Use epilog’s CO2 laser to process this 2D data matrix code. Our fiber laser can also mark the same white layer, but the contrast is not high.

3) The engraving passes through the PCB material to expose the copper layer.

Epilog’s fibermark and fusion M2 fiber lasers are able to carve on PCB material to expose the copper layer below. Because the layer is too thin, fiber lasers can also cut through the material.
Powrót do góry
Ogląda profil użytkownika Wyślij prywatną wiadomość
Reklama






Wysłany: Wto Sty 19, 2021 18:28    Temat postu:

Powrót do góry
Wyświetl posty z ostatnich:   
Napisz nowy temat   Odpowiedz do tematu    Forum Lambert Benjamin Strona Główna -> milgetfstanel Wszystkie czasy w strefie CET (Europa)
Strona 1 z 1
Skocz do:  
Nie możesz pisać nowych tematów
Nie możesz odpowiadać w tematach
Nie możesz zmieniać swoich postów
Nie możesz usuwać swoich postów
Nie możesz głosować w ankietach

Lambert Benjamin  

To forum działa w systemie phorum.pl
Masz pomysł na forum? Załóż forum za darmo!
Forum narusza regulamin? Powiadom nas o tym!
Powered by Active24, phpBB © phpBB Group